Corrosion-resistant instrumentation for sugar mills uses stainless steel on every part that touches the process. A diaphragm seal protects instruments on juice and syrup lines. Radar level sensors work in steamy tanks, but you must match the type to the liquid. Check material, temperature, and pressure before you order.
Acidic juice and condensate cause most of the damage. A study found condensate with a pH below 5, which corroded carbon steel pipework, valves, and tube plates. In the same study, Type 304 stainless steel showed very low corrosion.
Four conditions can wear instruments down:
Use stainless steel for all the parts that touch the fluid. These parts need to be made from a material that can safely handle the fluid without corroding or getting damaged.
The WIKA All S.S 4-inch pressure gauge has 316L stainless steel parts that touch the fluid and a 304 stainless steel case. It has IP65 protection and ±1.0% accuracy, and it can handle fluids up to 392°F (200°C).
This model has a back connection, which makes it suitable for panel or recessed mounting. For pipe-mounted lines, choose a bottom-connection model from the pressure gauge range. If the line has sudden pressure changes, add a snubber from the pressure accessories range. It is also important to keep the connected fittings made of stainless steel.
A diaphragm seal is a thin, flexible membrane that separates the instrument from the process fluid. This helps prevent clogging, crystallization, and corrosion inside the gauge or transmitter.
The Diaphragm Seal With Flange Connection (Model 990.27) is listed for aggressive, highly viscous, crystallizing, or hot fluids. This makes it suitable for juice, syrup, and evaporator lines. It has:
Tell SS Hussain your fluid so they can confirm the diaphragm material. You can also see the full diaphragm seal range for other connection types.
For easy-clean points, the Diaphragm Seal With Sterile Connection and Clamp (Model 990.22) meets 3-A and ASME BPE standards. It suits CIP and SIP cleaning. CIP means clean-in-place, while SIP means steam-in-place.
The SP 2088 pressure transmitter has a 316L stainless steel wetted diaphragm. It gives a 4-20 mA output and runs on 24 V DC, with accuracy of 0.2% or 0.5%. Its fluid temperature can range from -40°C to 120°C.
Steam above about 1 bar gauge is hotter than 120°C, so hotter lines need a seal with a cooling element. On juice lines, mount a flange seal in front of the transmitter.
You can use radar level sensors in sugar mill tanks. Choose the type by the liquid in the tank. Non-contact radar suits sticky or steamy tanks. Guided wave radar suits clean liquids.
The 26G High Frequency Radar Level Meter measures from above. No probe sits in the liquid, so juice or syrup is less likely to coat the sensor. This makes it a good option for juice, syrup, and molasses tanks. Ask before purchasing for its range, accuracy, and antenna material before ordering.
The Guided Wave Radar Level Meter works up to 400°C and 400 bar. It has ±3 mm accuracy, with 4-20 mA and HART outputs. It uses a probe inside the tank, so buildup or coating on the probe can affect it. It also does not suit turbulent surfaces. Use it on clean liquids such as condensate and water. Browse all level meters for other options.
Follow these steps before crushing season:
Stainless steel suits steam and condensate lines. For sticky, crystallizing, or very corrosive fluids such as juice and syrup, add a diaphragm seal.
Only below its 120°C fluid limit. For hotter steam, use a diaphragm seal with a cooling element.
Use non-contact radar. Guided wave radar can be affected by coating on the probe.
Send your fluid, pressure, and temperature by WhatsApp to +92 319 3961178 or email info@sshussain.com. You can also use the contact page.
Corrosion-resistant instrumentation for sugar mills comes down to material, protection, and sensor choice. Use stainless wetted parts, fit diaphragm seals on juice and syrup lines, and match each level sensor to its liquid. Calibrate before crushing season starts. Contact us with your process details, and we will recommend the right instruments.