Most pharma plants calibrate critical pressure gauges every 6 months and monitoring-only gauges every 12. GMP rules don’t give you one fixed number. Your plant sets the interval based on risk, writes it down, and then sticks to it. If a gauge takes a shock or an overpressure hit, calibrate it sooner.
Pressure gauges in a pharma plant need regular calibration so the readings stay accurate. Calibration just means checking a gauge against a known reference and adjusting it if it’s off. You’ll find gauges on autoclaves, cleanroom air pressure systems, filters and process vessels. A gauge that reads wrong can hurt product quality; it can also cause trouble in an audit. This guide covers how often to calibrate and how to build a schedule you can defend when the auditor shows up.
Critical gauges usually go every 6 months, monitoring-only gauges every 12. That’s common industry practice, not a legal requirement.
Start critical gauges at 6 months and monitoring-only gauges at 12, then adjust using your own risk assessment and calibration history.
GMP wants calibration at suitable intervals. It doesn’t say how many months. The US FDA rule, 21 CFR Part 211, calls for calibration under a written program, and EU GMP and WHO GMP both expect traceable standards and proper records.
No single interval fits every gauge. So what auditors actually check is whether your schedule is justified, written down, and followed.
The more a gauge’s reading affects the process, the shorter its interval should be. Here’s what’s typical, depending on how the gauge is used.
| Gauge use | Typical interval | Reason |
| Autoclave or sterilizer | 6 months | Critical to the process |
| Cleanroom differential pressure | 6 months | Shows room pressure difference |
| Process vessel or line | 6 months | Critical to the process |
| Utility or non-critical monitoring | 12 months | Monitoring only |
For differential pressure readings, SS Hussain & Sons supplies an all stainless steel differential pressure gauge (KPG-5352A).
Four things. How critical the gauge is, the conditions it runs in, how it has done in past calibrations, and what the manufacturer says.
Look at the interval again after every calibration, and change it when the results tell you to.
Don’t wait for the next scheduled date if something could have thrown the gauge off. Calibrate it right away when:
A record should show what you tested, how you tested it, and what you found. Keep it all together; that way you can track the gauge’s accuracy over time and hand over evidence during an audit.
Each record needs:
Once calibration is done, stick a label on the gauge with its status and next due date.
If a gauge is out of tolerance, pull it from use and quarantine it. Then look at which products were made since its last good calibration and work out whether the bad reading could have affected them. Auditors look hard at this step.
SS Hussain & Sons calibrates pressure gauges and pressure transmitters, which keeps your instruments accurate and your operations safe. Wear, vibration and temperature swings make readings drift over time. Regular calibration catches that before it hits product quality or compliance.
Every instrument goes to a trusted third-party laboratory, so you get impartial results you can rely on for audits and quality records. Your calibration certificate comes back in 24 to 48 hours, so downtime stays small.
Explore our calibration services or contact us to arrange calibration for your pressure instruments.
You can also buy pressure gauges and pressure transmitters here, including Kipinago and TrueTeller brands. Contact SS Hussain & Sons for a quote.
For monitoring-only gauges, often yes. Critical gauges are usually done every 6 months. Your risk assessment decides the actual interval.
Yes, if past results show the gauge stays within tolerance. Write down the reason and get QA approval.
Yes. Check it against a reference standard and record the result before it goes into service.
Quarantine it and investigate the failure. Check which products were made since its last good calibration, then record what you found.
Trained staff can do it in-house, or you can use an external service. Either way you need traceable reference standards, and the calibration lab should give you a certificate for your records.
Start with 6 months for critical pressure gauges and 12 months for monitoring-only ones. Then adjust for risk, working conditions and past calibration results, and calibrate sooner after any shock or overpressure. Keep complete records, because you’ll need to explain to an auditor why you picked each interval.